Difficult
How to glue Plasterboard to Plasterboard
The short answer
A grab adhesive is the best-supported starting point for Plasterboard to Plasterboard. The exact pair is an evidence-based assessment from the cited manufacturer scopes, not a manufacturer-tested pair claim. Prepare both faces as specified, maximise overlap, minimise peel and validate a representative coupon before critical use.
Why this bond behaves the way it does
A grab adhesive matches the joint's porosity, stiffness and gap needs better than the listed alternatives. The recommendation is graded C because the manufacturer evidence supports the constituent substrate classes but does not report this exact pair.
What to use
Best choice
Grab adhesive, no-nails
Use a grab adhesive as the first route because the cited product and preparation documents cover the controlling substrate classes. This exact pair remains an explicit inference.
Gaps: Maintain the bond line stated by the manufacturer and do not clamp it dry.
Curing: Do not confuse initial grab or handling strength with full cure.
Watch out: Coupon-test the exact substrate grades and surface finish.
Also works
MS polymer
A flexible MS-polymer adhesive is an alternative only when a current product document covers both actual faces, the bond-line thickness and the service environment.
Gaps: Maintain the bond line stated by the manufacturer and do not clamp it dry.
Curing: Do not confuse initial grab or handling strength with full cure.
Watch out: Coupon-test the exact substrate grades and surface finish.
Also works
Polyurethane adhesive
A polyurethane adhesive is an alternative only when a current product document covers both actual faces, the bond-line thickness and the service environment.
Gaps: Maintain the bond line stated by the manufacturer and do not clamp it dry.
Curing: Do not confuse initial grab or handling strength with full cure.
Watch out: Coupon-test the exact substrate grades and surface finish.
Avoid
Cyanoacrylate
Avoid a primed cyanoacrylate for a load-bearing, gapped or exposed joint unless its current technical sheet names the substrates and service conditions. Do not bond over oil, rust, dust, glaze, release agent or weak surface fibres.
Gaps: Use only on the thin, close-fitting joint stated by the exact grade.
Curing: Do not confuse initial grab or handling strength with full cure.
Watch out: This avoidance is for the ordinary unqualified family, not a specialist grade with explicit manufacturer evidence.
What to avoid
Avoid a primed cyanoacrylate for a load-bearing, gapped or exposed joint unless its current technical sheet names the substrates and service conditions. Do not bond over oil, rust, dust, glaze, release agent or weak surface fibres.
Preparing the surfaces
Plasterboard
Confirm that the paper face, skim coat or paint is firmly attached. Keep the background dry, remove dust, grease and loose material, and cut away torn paper. Use broad adhesive dabs or beads as the named system specifies. Do not rely on adhesive alone for loads that exceed the board or facing strength.
Plasterboard
Confirm that the paper face, skim coat or paint is firmly attached. Keep the background dry, remove dust, grease and loose material, and cut away torn paper. Use broad adhesive dabs or beads as the named system specifies. Do not rely on adhesive alone for loads that exceed the board or facing strength.
How to do it
Dry-fit first. Meter, mix or prime exactly as the selected product requires. Apply a controlled bond line, assemble within working time, clamp without squeezing the joint dry and leave supported through the full stated cure.
Working, clamping and cure times
Follow the current Sika Gun a Nail instructions. Working time, handling strength and full cure are different. Cold conditions, thick beads and two impermeable faces can extend the cure.
If the conditions are harder
| Condition | Verdict | Notes |
|---|---|---|
| Outdoor use | Not enough evidence | The cited product evidence does not establish a complete outdoor system for this exact pair, including UV, freeze-thaw, edge sealing and differential movement. |
| Water and wet areas | Not enough evidence | No cited document establishes continuous wet service for the exact pair. Keep it dry until a product-specific exposure test or specification is available. |
| Heat and cold | Works with care | The product record states an upper service temperature of 70 degrees C and a lower service temperature of -10 degrees C. Use the narrower limit of the adhesive, both substrates, any coating and the joint design. |
Read the current safety data sheet. Provide ventilation, protect skin and eyes, and test an offcut for solvent attack, staining, stress cracking or coating lift. This is not an engineering approval for safety-critical loads.
Products that fit
Ordered by how well they suit this specific job. Nothing is ranked by what it pays.
Sika Sika Gun a Nail
Grab adhesive, no-nails
The manufacturer documentation covers the controlling substrate class, but this exact dissimilar pair remains an assessed use requiring a coupon test.
We may earn a commission from links on this page. It never changes which adhesive we recommend.
Related guides
Where this comes from
Reviewed 8 October 2026. Overall confidence: Inferred.
Sources used for this guide:
- 3M Bonding Solutions: Adhesives and Tapes Selection Guide (TECHNICAL_MANUAL)
- Gyproc DriWall Adhesive Product Data Sheet (PDS)
- Permabond Adhesive Application Tips (MANUFACTURER_PAGE)
- Sika Gun a Nail Product Data Sheet (PDS, Nov 2025)
- Surface Preparation (MANUFACTURER_PAGE)
- Surface Preparation and Pretreatment for Structural Adhesives (TECHNICAL_MANUAL, Oct 2018)
Always read the instructions and safety information supplied with the product you buy. Where they differ from anything here, follow the manufacturer.